Popular fittings › Oval duct adapter
Oval duct adapter
Low-profile oval ducting with independent width and height. Free 3D printable adapter, export 3MF, STL or STEP.
Open in the designer →
Opens with the sizes below. Change anything, then export 3MF, STL or STEP. Free, no account, runs in your browser.
Starting sizes
| End | Inner size | Connection |
|---|---|---|
| Inlet | 100 mm (3.94 in) | Smooth sleeve |
| Outlet | 130 × 45 mm | Smooth sleeve |
Need another size? Every dimension is editable in the designer, in millimetres or inches.
What it is
Connects oval or flattened duct to round hose, for runs with little height to spare.
How to measure
For a rectangular end, measure the inside width and height of the duct or opening it joins, or its outside size if the fitting slides inside it. For each end, measure the hose, pipe or port it joins with calipers. If that part slides into the fitting, measure its outside diameter and keep “Measure by: Inner diameter”. If the fitting slides into a hose, measure the hose’s inside diameter and switch to “Outer diameter”. Measure twice across the circle; flexible hose is rarely perfectly round.
Print tips
- The export already places every component in its recommended print orientation. Keep supports off sleeves, sockets and any sliding or tight-fit surface so they stay smooth; if your slicer asks for supports, paint them only where an outside overhang needs them.
- Use 3–4 perimeters for an airtight wall; infill matters much less than wall count for ducts.
Frequently asked questions
- What size should I measure?
- For a rectangular end, measure the inside width and height of the duct or opening it joins, or its outside size if the fitting slides inside it. For each end, measure the hose, pipe or port it joins with calipers. If that part slides into the fitting, measure its outside diameter and keep “Measure by: Inner diameter”. If the fitting slides into a hose, measure the hose’s inside diameter and switch to “Outer diameter”. Measure twice across the circle; flexible hose is rarely perfectly round.
- What should I print it in?
- PLA or PETG both work for dust collection at room temperature. Print in PETG or ASA if the air is warm or the part sits in the sun. Use 3–4 perimeters for an airtight wall; infill matters much less than wall count for ducts.
- What hardware do I need to buy?
- Nothing is required at these starting sizes: it prints in one piece. A hose clamp is optional if a hose feels loose.
- Does it need supports?
- The export already places every component in its recommended print orientation. Keep supports off sleeves, sockets and any sliding or tight-fit surface so they stay smooth; if your slicer asks for supports, paint them only where an outside overhang needs them.
More popular fittings
100 mm to 4 inch duct adapterJoin metric 100 mm duct to 4 inch (101.6 mm) hose. Free 3D printable adapter you can resize, then export as 3MF, STL or STEP.
Shop vac 2.5 inch to 35 mm hose adapterConnect a 2.5 inch shop vacuum hose to a 35 mm power tool dust port. Free 3D printable adapter, every dimension adjustable.
4 inch to 2.5 inch reducerConnect 4 inch dust collection to 2.5 inch shop vac hose with a gradual 3D printable reducer. Every dimension adjustable.
6 inch to 4 inch reducerA 3D printable 6 inch to 4 inch duct reducer for dust collectors, fans and exhaust. Free, adjustable, export 3MF, STL or STEP.
150 mm to 100 mm reducerA 3D printable 150 mm to 100 mm duct reducer for inline fans, extraction and ventilation. Every dimension adjustable.
125 mm to 100 mm reducerA 3D printable 125 mm to 100 mm duct reducer for inline fans and ventilation hose. Free and fully adjustable.